G-Stomper 2.6.5 has been released!

Questions and Discussions about G-Stomper
User avatar
planet-h
Posts: 1473
Joined: Wed Jun 19, 2013 4:46 pm

G-Stomper 2.6.5 has been released!

Postby planet-h » Fri Jul 05, 2013 10:11 am

G-Stomper 2.6.5 is online!
First of all, very special thanks to to all who helped in beta testing.

Here is what you get this time:

Major improvements in the Effect section
Much more control: most effects have now 4 automatable parameters
New bpm synchable LFOs for: EQ1, Filters, Delays, Enhancers, Vibrato, Auto Panner, Chorus, Phaser
LFO Waveforms: Triangle, Saw, Reversed Saw, Pulse, Random, Smooth Random
Fixed Parameter assignment when changing the effect type on the efx and master screen
Fixed sync timing for LFOs and X-Delay
Fixed a memory issue on large screens with low resolutions
Fixed the progressBars for Android 2.x

The latest UserManual can be donwloaded at: http://www.planet-h.com/gstomper/

Final effect parameter reference:

Compressor/Limiter:
Parameter 1: Threshold (-30..-0dB)
Parameter 2: AT:Ratio (1:12..12:1)
Parameter 3: Attack (7..200ms)
Parameter 4: Release (50..500ms)

Compressor (simple):
Parameter 1: Sensitivity (0..100)
Parameter 2: Attack (7..200ms)
Parameter 3: Release (50..500ms)
Parameter 4: -

Limiter (simple):
Parameter 1: Sensitivity (0..100)
Parameter 2: Release (50..500ms)
Parameter 3: -
Parameter 4: -

Chorus/Flanger:
Parameter 1: Speed (1000s..50Hz | 16/1..1/64)
Parameter 2: Depth (0..100)
Parameter 3: Delay (1..15ms)
Parameter 4: phase invert (ON/OFF)

Phaser:
Parameter 1: Speed (100s..50Hz | 16/1..1/64)
Parameter 2: Depth (0..100)
Parameter 3: color (0..100)
Parameter 4: phase invert (ON/OFF)

Static Phaser (no LFO):
Parameter 1: Sweep (0..100)
Parameter 2: Depth (0..100)
Parameter 3: color (0..100)
Parameter 4: phase invert (ON/OFF)

Vibrato:
Parameter 1: Speed (100s..261.63Hz | 16/1..1/64)
Parameter 2: Depth (0..100)
Parameter 3: -
Parameter 4: -
(LFO assigned to the output volume)

Auto Panner:
Parameter 1: Speed (100s..261.63Hz | 16/1..1/64)
Parameter 2: Depth (0..100)
Parameter 3: -
Parameter 4: -
(LFO assigned to the output panorama)

X-Delay:
Parameter 1: Delay (2..1000ms | 1/64..1/4)
Parameter 2: Feedback (0..100)
Parameter 3: LFO:speed (100s..50Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p2:feedback)

Short Delay:
Parameter 1: Delay (2..150ms)
Parameter 2: Feedback (0..100)
Parameter 3: LFO:speed (100s..50Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p2:feedback)

Reverb:
Parameter 1: Time (0..2000ms)
Parameter 2: Mix dry/wet (0..100)
Parameter 3: pre-delay (1..500ms | 1/64..1/8)
Parameter 4: damping (0..100)

Pitch Shifter:
Parameter 1: Pitch1 (0..100)
Parameter 2: Mix dry/wet (0..100)
Parameter 3: Pitch2 (an additional pitch shifter to mix to the wet signal)
Parameter 4: Pitch2:level (0..100)

Stereo Enhancer:
Parameter 1: L:Delay (0..30ms)
Parameter 2: R:Delay (0..30ms)
Parameter 3: LFO:speed (100s..50Hz | 16/1..1/64)
Parameter 4: HP:freq (328..8000Hz) only the signal above this frequency gets enhanced
(LFO cycles the stereo room)

Exciter:
Parameter 1: Tune:HP (1200..9000Hz) only the signal above this frequency gets enhanced
Parameter 2: Drive (0..100)
Parameter 3: LFO:speed (100s..50Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p2:drive)

Bottom Booster:
Parameter 1: Tune:LP (0..100) only the signal below this frequency gets enhanced
Parameter 2: Drive (0..100)
Parameter 3: LFO:speed (100s..50Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p2:drive)

BitCrusher:
Parameter 1: Bit-Depth (16..2.58bit)
Parameter 2: SampleRate (44100..500Hz)
Parameter 3: EQ:gain (-100..+100)
Parameter 4: EQ:freq (100..10000Hz)

Waveshaper:
Parameter 1: Gain (0..100)
Parameter 2: Waveform (W-01..W-05)
Parameter 3: EQ:gain (-100..+100)
Parameter 4: EQ:freq (100..10000Hz)

Distortion:
Parameter 1: Gain (0..100)
Parameter 2: Level (0..100)
Parameter 3: EQ:gain (-100..+100)
Parameter 4: EQ:freq (100..10000Hz)

Bender Distortion:
Parameter 1: Gain (0..100)
Parameter 2: Level (0..100)
Parameter 3: EQ:gain (-100..+100)
Parameter 4: EQ:freq (100..10000Hz)

LP Filter 24dB:
Parameter 1: Cutoff (0..14000Hz)
Parameter 2: Resonance (0..100)
Parameter 3: LFO:speed (100s..261.63Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p1:cutoff)

LP Filter 12dB:
Parameter 1: Cutoff (0..14000Hz)
Parameter 2: Resonance (0..100)
Parameter 3: LFO:speed (100s..261.63Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p1:cutoff)

HP Filter 24dB:
Parameter 1: Cutoff (0..14000Hz)
Parameter 2: Resonance (0..100)
Parameter 3: LFO:speed (100s..261.63Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p1:cutoff)

HP Filter 12dB:
Parameter 1: Cutoff (0..14000Hz)
Parameter 2: Resonance (0..100)
Parameter 3: LFO:speed (100s..261.63Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p1:cutoff)

BP Filter 12dB:
Parameter 1: Cutoff (0..14000Hz)
Parameter 2: Resonance (0..100)
Parameter 3: LFO:speed (100s..261.63Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p1:cutoff)

Notch Filter 12dB:
Parameter 1: Cutoff (0..14000Hz)
Parameter 2: Resonance (0..100)
Parameter 3: LFO:speed (100s..261.63Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p1:cutoff)

Moog LP Filter 24dB:
Parameter 1: Cutoff (0..14000Hz)
Parameter 2: Resonance (0..100)
Parameter 3: LFO:speed (100s..261.63Hz | 16/1..1/64)
Parameter 4: LFO:depth (0..100)
(LFO assigned to p1:cutoff)

EQ (2-Band):
Parameter 1: Gain1 (0..100)
Parameter 2: Gain2 (0..100)
Parameter 3: Freq1 (100..10000Hz)
Parameter 4: Freq2 (100..10000Hz)

EQ (1-Band):
Parameter 1: EQ:gain (-100..+100)
Parameter 2: EQ:freq (100..10000Hz)
Parameter 3: LFO:speed 50Hz | 16/1..1/64)
Parameter 4: LFO:depth
(LFO assigned to p2:frequency)

Hope you're enjoying the new effect rack

Return to “General Questions and Discussions”

Who is online

Users browsing this forum: No registered users and 3 guests